Dielectric heating

Dielectric heating, also known as electronic heating, radio frequency heating, and high-frequency heating, is the process in which a radio frequency (RF) alternating electric field, or radio wave or microwave electromagnetic radiation heats a dielectric material. At higher frequencies, this heating is caused by molecular dipole rotation within the dielectric. Dielectric heating, also known as electronic heating, radio frequency heating, and high-frequency heating, is the process in which a radio frequency (RF) alternating electric field, or radio wave or microwave electromagnetic radiation heats a dielectric material. At higher frequencies, this heating is caused by molecular dipole rotation within the dielectric. RF dielectric heating at intermediate frequencies, due to its greater penetration over microwave heating, shows greater promise than microwave systems as a method of very rapidly heating and uniformly preparing certain food items, and also killing parasites and pests in certain harvested crops. Molecular rotation occurs in materials containing polar molecules having an electrical dipole moment, with the consequence that they will align themselves in an electromagnetic field. If the field is oscillating, as it is in an electromagnetic wave or in a rapidly oscillating electric field, these molecules rotate continuously by aligning with it. This is called dipole rotation, or dipolar polarisation. As the field alternates, the molecules reverse direction. Rotating molecules push, pull, and collide with other molecules (through electrical forces), distributing the energy to adjacent molecules and atoms in the material. The process of energy transfer from the source to the sample is a form of radiative heating. Temperature is related to the average kinetic energy (energy of motion) of the atoms or molecules in a material, so agitating the molecules in this way increases the temperature of the material. Thus, dipole rotation is a mechanism by which energy in the form of electromagnetic radiation can raise the temperature of an object. There are also many other mechanisms by which this conversion occurs. Dipole rotation is the mechanism normally referred to as dielectric heating, and is most widely observable in the microwave oven where it operates most effectively on liquid water, and also, but much less so, on fats and sugars. This is because fats and sugar molecules are far less polar than water molecules, and thus less affected by the forces generated by the alternating electromagnetic fields. Outside of cooking, the effect can be used generally to heat solids, liquids, or gases, provided they contain some electric dipoles. Dielectric heating involves the heating of electrically insulating materials by dielectric loss. A changing electric field across the material causes energy to be dissipated as the molecules attempt to line up with the continuously changing electric field. This changing electric field may be caused by an electromagnetic wave propagating in free space (as in a microwave oven), or it may be caused by a rapidly alternating electric field inside a capacitor. In the latter case, there is no freely-propagating electromagnetic wave, and the changing electric field may be seen as analogous to the electric component of an antenna near field. In this case, although the heating is accomplished by changing the electric field inside the capacitive cavity at radio-frequency (RF) frequencies, no actual radio waves are either generated or absorbed. In this sense, the effect is the direct electrical analog of magnetic induction heating, which is also near-field effect (thus not involving radio waves). Frequencies in the range of 10–100 MHz are necessary to cause dielectric heating, although higher frequencies work equally well or better, and in some materials (especially liquids) lower frequencies also have significant heating effects, often due to more unusual mechanisms. For example, in conductive liquids such as salt water, ion-drag causes heating, as charged ions are 'dragged' more slowly back and forth in the liquid under influence of the electric field, striking liquid molecules in the process and transferring kinetic energy to them, which is eventually translated into molecular vibrations and thus into thermal energy. Dielectric heating at low frequencies, as a near-field effect, requires a distance from electromagnetic radiator to absorber of less than 1/2π ≈ 1/6 of a wavelength. It is thus a contact process or near-contact process, since it usually sandwiches the material to be heated (usually a non-metal) between metal plates taking the place of the dielectric in what is effectively a very large capacitor. However, actual electrical contact is not necessary for heating a dielectric inside a capacitor, as the electric fields that form inside a capacitor subjected to a voltage do not require electrical contact of the capacitor plates with the (non-conducting) dielectric material between the plates. Because lower frequency electrical fields penetrate non-conductive materials far more deeply than do microwaves, heating pockets of water and organisms deep inside dry materials like wood, it can be used to rapidly heat and prepare many non-electrically conducting food and agricultural items, so long as they fit between the capacitor plates. At very high frequencies, the wavelength of the electromagnetic field becomes shorter than the distance between the metal walls of the heating cavity, or than the dimensions of the walls themselves. This is the case inside a microwave oven. In such cases, conventional far-field electromagnetic waves form (the cavity no longer acts as a pure capacitor, but rather as an antenna), and are absorbed to cause heating, but the dipole-rotation mechanism of heat deposition remains the same. However, microwaves are not efficient at causing the heating effects of low frequency fields that depend on slower molecular motion, such as those caused by ion-drag.