Tension (physics)

In physics, tension may be described as the pulling force transmitted axially by the means of a string, cable, chain, or similar one-dimensional continuous object, or by each end of a rod, truss member, or similar three-dimensional object; tension might also be described as the action-reaction pair of forces acting at each end of said elements. Tension could be the opposite of compression. In physics, tension may be described as the pulling force transmitted axially by the means of a string, cable, chain, or similar one-dimensional continuous object, or by each end of a rod, truss member, or similar three-dimensional object; tension might also be described as the action-reaction pair of forces acting at each end of said elements. Tension could be the opposite of compression. At the atomic level, when atoms or molecules are pulled apart from each other and gain potential energy with a restoring force still existing, the restoring force might create what is also called tension. Each end of a string or rod under such tension could pull on the object it is attached to, in order to restore the string/rod to its relaxed length. In physics, tension, as a transmitted force, as an action-reaction pair of forces, or as a restoring force, may be a force and has the units of force measured in newtons (or sometimes pounds-force). The ends of a string or other object transmitting tension will exert forces on the objects to which the string or rod is connected, in the direction of the string at the point of attachment. These forces due to tension are also called 'passive forces'. There are two basic possibilities for systems of objects held by strings: either acceleration is zero and the system is therefore in equilibrium, or there is acceleration, and therefore a net force is present in the system. Tension in a string is a scalar quantity (i.e. non-negative). Zero tension is slack. A string or rope is often idealized as one dimension, having length but being massless with zero cross section. If there are no bends in the string, as occur with vibrations or pulleys, then tension is a constant along the string, equal to the magnitude of the forces applied by the ends of the string. By Newton's Third Law, these are the same forces exerted on the ends of the string by the objects to which the ends are attached. If the string curves around one or more pulleys, it will still have constant tension along its length in the idealized situation that the pulleys are massless and frictionless. A vibrating string vibrates with a set of frequencies that depend on the string's tension. These frequencies can be derived from Newton's laws of motion. Each microscopic segment of the string pulls on and is pulled upon by its neighboring segments, with a force equal to the tension at that position along the string. tension = τ ( x ) {displaystyle = au (x)} where x {displaystyle x} is the position along the string. If the string has curvature, then the two pulls on a segment by its two neighbors will not add to zero, and there will be a net force on that segment of the string, causing an acceleration. This net force is a restoring force, and the motion of the string can include transverse waves that solve the equation central to Sturm-Liouville theory: − d d x [ τ ( x ) d ρ ( x ) d x ] + v ( x ) ρ ( x ) = ω 2 σ ( x ) ρ ( x ) {displaystyle -{frac {d}{dx}}{igg }+v(x) ho (x)=omega ^{2}sigma (x) ho (x)} where v ( x ) {displaystyle v(x)} is the force constant per unit length , ω 2 {displaystyle omega ^{2}} are the eigenvalues for resonances of transverse displacement ρ ( x ) {displaystyle ho (x)} on the string., with solutions that include the various harmonics on a stringed instrument. Tension is also used to describe the force exerted by the ends of a three-dimensional, continuous material such as a rod or truss member. Such a rod elongates under tension. The amount of elongation and the load that will cause failure both depend on the force per cross-sectional area rather than the force alone, so stress = axial force / cross sectional area is more useful for engineering purposes than tension. Stress is a 3x3 matrix called a tensor, and the σ 11 {displaystyle sigma _{11}} element of the stress tensor is tensile force per area, or compression force per area, denoted as a negative number for this element, if the rod is being compressed rather than elongated.